1963 Jaguar E-Type OTS
The story of a ground up restoration of a classic "XKE" Jaguar roadster

Right Sill Stiffeners, Rear Bulkhead, Some Priming (23 - 24 November 2002)

 
Navigation
RESTORATION JOURNAL
PHOTOS & PARTS
PAINT INFO & CODES
USEFUL RESOURCES
TERMS & CONDITIONS
c h r o n o l o g i c a l
g u i d e

> Year 1   Year 2 <
> Year 3   Year 4 <
> Year 5   Year 6 <
> Year 7   Year 8 <
> Year 9   Year 12 <

fetching & dismantling
sandblasting & evil rust
right "b" pillar
fixing right inner sill
basic body repair, por-15
frame removed, footwell repair
hole fixed, car flipped, etc.
sill stiffeners, rear bulkhead, etc.
various small parts
left sill, added stiffener, etc.
   - lousy weather
trunk floor (reprise)
right floor, left sill, etc.
left floor, wheel well, etc.
right upper wishbone
floor done, car righted
rack, front frame, evil rust
left door cleaned & fitted
right door, right suspension
bonnet, part 1
bonnet, part 2
bonnet, part 3
bonnet, part 4
bonnet, part 5, etc.
bonnet, part 6
bonnet, outer sill, etc.
lots of stuff
left side, bonnet internals
frame, bonnet attached
engine stand, oil pan removal
pistons removed, sanding
sanding, final filling
color, frames, primer
brushed primer test
2nd coat primer
holiday greetings!
finish prep, detail on dent fix
spraying primer
winter chores
  1. undercoat, plating prep
  2. plating, spraying color
bonnet, plate prep, cylinder head
cylinder head paint, bushes
plating saga
front frame, suspension, part 1
front suspension, part 2
front suspension, part 3
priming and painting
bonnet, part 7
painting color!
boot lid, steering wheel
gas tank
winter chores
  1. firewall sundry
  2. front suspension
  3. steering setup
  4. master cylinders/pedals
  5. the rest
data plate screed
winter to spring
  1. irs rebuild
  2. trunk floor, harness
  3. data plate (again)
data plate, door, headlights
dash vinyl, crosshatch aluminum
windshield, right door
interior, "widget"
chrome parts!
door handle details
rolling chassis
molasses rust removal
electrical, part 1
bores, thrust washers
new engine!
head differences
block differences
compression ratio
engine in place!
alternator
catchup & photos
it runs!
setback and brakes
darned close & engine diffs
driven
top and seats
driving and little stuff

Right Sill Stiffeners, Rear Bulkhead, Some Priming (23 - 24 November 2002)

Right Sill Stiffeners

After the manufacture and installation of the sill end pieces on the right sill, I installed the front and rear sill stiffeners. These are little more than brackets that fit below the door frames — below the "B"-pillar in the rear and below the structure that holds the door hinges. They turn the (roughly) square sill into two triangles, and that's why they are so good at stiffening the sills. I was thinking about putting a third sill stiffener in between the front and rear stiffeners, but after I got them in, it seemed as though there really wasn't that much room between the stiffeners. At least not much to worry about. (I have seen a third stiffener installed by some restorers. They use a modified front stiffener.)

I had to fabricate the rear stiffener myself, and I used the existing rear stiffener on the left side of the car as a guide. That stiffener is intact, and it needs a little repair. I just created a template out of cardboard (the side of a Budweiser 24-pack), and tested it out by folding it and placing it into the sill. Once I was happy with the fit, I just cut the metal, leaving a little bit extra material so that I could trim it down after bending it. I installed both stiffeners with spot welds.

They really do firm up the sill.

Rear Bulkhead, Some Priming

The right rear bulkhead, you might recall, was pretty badly corroded about two inches up from the floor panel and nearest the sill side. I cut out all of the corrosion, cleaned up the internal structure that supports the rear bulkhead, welded in some tabs, and spot welded new metal cut the same shape as the area I had removed. After grinding it all flat as best I could, I put a thin layer of Bondo to smooth out the surface. After sanding, I primed the rebuilt rear bulkhead and the right inner sill. You might notice that I "missed" a small area about halfway along the sill. Actually, I didn't prime that area, since I'll need to weld the cross-member to the sill at about that point. I figured I didn't want to cook my primer! I also primed the right rear wheel well, which I scraped and scraped and scraped to get off the various coatings of rustproofing and greasy girt.

Need Radius Arm Mounting Cups

I'm just about ready to install the right floor panel. I have a bit of sheet metal repair to do near the engine/transmission wall, but that is fairly trivial. After I installed the floors I was hoping to be able to install the "radius arm mount cups" — little fittings that hold the arms that come front from the independent rear suspension. But, the mounting cups need to be put into place before the floor goes on. Some of the holes intended for hardware are not accessible after the floor is fitted, since they are then entombed in the rear bulkhead. So I have to get at least one new mounting cup, possibly two. The mounting cup that we removed from the right side was damaged by the cutting tool, and it was at any rate pretty badly damaged by rust.

The mounting cup on the left floor is in better shape, and I will know more about its usefulness after I get it off. I'll probably grind the hardware off on Monday night and take a closer look. If it is serviceable, we'll probably use it on the right side after we clean it up and rust-protect it. I want to get on with the floor panel installation, so that we can prime, rock-guard, and paint the underside of the car. Then we can get it back right-side up, and move on to some mechanical work!