Through January I did some extra work for some extra cash (for extra parts for the Jag). As a result, I spent very little time in the garage. It has been very cold in
North Carolina this winter, and January wasn't the best time to do much of anything without a good heater. The garage space heater just can't keep up when it gets
I did work on a database of pictures and notes for this site, and I hope to let that have its debut in the next couple of weeks. I have a lot of pictures
taking up in excess of 500 megabytes. So, I have to be ingenious about making them available on the web. My intent with the database is to show the process of this
restoration in a clear and searchable manner. If I can do that, other restorerers might find it useful, too.
UPDATE 16 February: This has been a winter to remember. We're probably going to get another ice storm
along the lines of the one that hit 5 December and stopped everything. People who wear aluminum foil hats (to ward off mind control devices)
might make a connection between my working on the car and ice storms. I just hope that the last ice storm took out the trees that would fall on power lines, so we might
be spared the darkness! Ice is already covering the ground, though only about a quarter inch so far.
Right Floor Installed (13 February 2003)
It's been five months since we picked up the car, and I am wondering if we are where I wanted to be with this project. I think we are close to the mark, though
I do wish we were done with metalwork on the "tub" the car body. We haven't touched the bonnet, we've done very little with the doors and the trunk lid,
and the engine and other mechanicals are practically untouched.
Getting a floor panel installed was a milestone, however. It seems a turning point from the putzy little fixes to something, well, substantial, even though the
the floor panel itself couldn't go on before the putzy little fixes were done.
Strictly speaking, the floor installation wasn't entirely "by the book." Rather than a simple spot-weld affair, as was the case with the original, we decided
to use bolts in certain places. No bolts are on the outside edge, since that edge has to accept the outer sill. But we placed bolts (5/16" width) at points along the edges
the crossmember and along the edge nearest the transmission. Three bolts are lined up along the front tab of the floor. Along the back we installed quarter-inch
bolts a little smaller so that they fit along the back lip on the floor panel. These bolts are grade 5, not stainless; but I figured that they will be covered
with rust-preventative POR-15 at any rate.
Installing the bolts makes spot welding easier, since the floor panel is held tight to the metal you're welding to. Since the bolts are for all practical purposes
invisible, I thought that this would be a good way of ensuring a tight floor fit without changing the car too much.
Aaron did most of the welding. After a bit of grinding to smooth out some lumpy welds, the entire surface was primed.
On Saturday, 15 February, we removed what remained of the left floor. In order to make sure that the floor area was structurally secure during the installation, we left
square tubular beam intact on the left floor area. This beam runs from front to back along the underside of the floor. Once the right floor was in place, the support (if
any) given to the body was no longer needed, so we cut it free and removed the vestiges of the left floor. This freed up the otherwise inaccessible space
behind the interior rear bulkhead and the part of the bulkhead that faces the independent rear suspension (IRS) a void of about 3-4 centimeters wide running laterally
across the car. I vacuumed the dust and dirt that had accumulated, brushed off what I could, and Rustoleum primed the entire inside of the void. I really wonder
why the car was designed to have this inaccessible area, since once the floor panels are on, you can't rustproof or paint anything in the void.
The picture was actually taken on 16 February, after I had primed the left sill interior. (You'll see the unprimed left sill below.)
We also did some repair of some hacked up section of the bell housing/transmission cover. This was a repair stupidity like the one we removed and repaired earlier,
though the affected area was much smaller. Like that other section on the opposite side of the car, this area had been cut with a pneumatic cutter, splotch welded and then
smeared with Bondo over fiberglass screen. It was nice to get real solid metal in the area. We also added some metal tabs along the perimeter where the floor panel rests.
Actually the tabs we added are too large, but we will cut them to size when we're ready to attach the floor with spot welds and bolts.
It's coming along.
Left Sill Stiffeners
I had finished the rebuilding of the inner sill in late December, as I recall, but the sill stiffeners weren't done yet. I kept the remains of the stiffeners
and these made good patterns at least for the sections that hadn't corroded. As I have with other parts I've fabricated, I made a cardboard template
and used it to fashion the piece. The stiffeners were made from 20-gauge steel, and I fashioned the middle stiffener from the design I used for the middle
stiffener done for the right sill. The secret is to be generous in your measurements for the tabs that you use to weld to the sill. It is easy to cut metal
away, but not so easy to add it.
This definitely looks much improved over the way we found the sill back at the end of November. There is still a fair amount of rebuilding
to do. The attachment piece for the front frame at the front portion of the inner sill needs to be completely rebuilt and solidly because of its
role in supporting the front end. I've decided not to use fabricated sheet metal at all for this (as was the case for the original). We'll put together something
with fortified angle iron which is thicker and stiffer than the original part. (Besides, I have the material on hand!)
POR-15 Applied to Trunk (14 February 2003)
This trunk seems to have taken longer than I expected at least it seems to occupy a fair number of these web pages. I'm hoping this picture will
do it for a while for the trunk. I applied the silver POR-15 over the primer, and it looks really good. That POR-15 is really solid stuff, and I am impressed
with it. I have to admit that I am not impressed with the recommended way of applying it, since the surface preparation never seemed to me to go just right.
I would run into small sections (smaller than the width of a pencil) that would seem to resist POR-15. I decided it would be easier, and probably just as
good, to prime the clean surface with Rustoleum primer and then apply the POR-15. This seems to work very nicely. The POR-15 bonds to the primer very well,
and surface preparation is much more straightforward, not a chemistry experiment.
Saturday, 15 February, is supposed to be warm, though rainy. Temperatures in the "Cat Cage" were around 60 degrees most of the day, and so doing the painting
was quite comfortable. POR-15 actually sets more quickly when the air is more humid, since the substance actually uses moisture as a hardener. Normally,
I don't like to paint in temperatures below, say, 65 degrees, but this worked out well.
The paint cured overnight to a hardness that feels very much like a "powder coating." I am tempted to spray it and perhaps use something other than the "silver"
brand. I've heard that the sprayed clear POR-15 dries very smoothly and is used as a primer coat for that reason. I am planning on coating the inner sills and
stiffeners very well probably a triple-coat of silver, just to ensure that the inner sills are well sealed from any moisture that might get into the area.